Crank seal stator side size

Post Reply
muaythaimaniac
Site Supporter
Site Supporter
Posts: 24
Joined: 25 Dec 2012, 11:37
Crank seal stator side size

Post by muaythaimaniac »

Hi all,

According to the forum the sizes for crank seals are 38x52x10 & 22x34x7... does anyone know which one of these is the stator side one? :?: ... I want to order it ready so I dont have to strip my bike down twice!

Thanks....
muaythaimaniac
Site Supporter
Site Supporter
Posts: 24
Joined: 25 Dec 2012, 11:37
Re: Crank seal stator side size

Post by muaythaimaniac »

No-one?.... I only want to know big seal or little seal!
fallenmikethebike
NWAA Supporter
NWAA Supporter
Posts: 3520
Joined: 02 Dec 2007, 16:02
Bike Owned: MK3
Location: Mid Surrey
Re: Crank seal stator side size

Post by fallenmikethebike »

Not without trawling through shed loads of old receipts.Perhaps on this occasion be a little reckless and order both, if you don't need it now it will be used at some time in the future.
The stator side is changed from the outside anyway, so that can be done at your leisure.
A bearing factor outlet store will have an almost identical size for considerably less than a dealer outlet.
Sorry to be negative but it's too cold out in my garage for poking about looking for stuff.
Mike
VFORCE REEDS-MUGEN HEAD AND BARREL-WHITE POWER-ALL ON MY WISH LIST!!
muaythaimaniac
Site Supporter
Site Supporter
Posts: 24
Joined: 25 Dec 2012, 11:37
Re: Crank seal stator side size

Post by muaythaimaniac »

Yep, the cold is whats putting me off taking it apart twice! :)
User avatar
knackeredMk1
Super Moderator
Super Moderator
Posts: 4185
Joined: 03 Nov 2006, 17:41
Bike Owned: Modified Mk1
Re: Crank seal stator side size

Post by knackeredMk1 »

If you look in the part diagrams in the FAQs you might get the answer ................?
User avatar
helisupp
NWAA Supporter
NWAA Supporter
Posts: 744
Joined: 12 Apr 2012, 21:57
Bike Owned: CRM AR (4)
Location: Gloucester
Re: Crank seal stator side size

Post by helisupp »

The Stator side is 22x34x7

Honda part number is 91203-KAE-003

Other one 38x52x10

is 91202-KAE-731
muaythaimaniac
Site Supporter
Site Supporter
Posts: 24
Joined: 25 Dec 2012, 11:37
Re: Crank seal stator side size

Post by muaythaimaniac »

Helisupp you are a star...nice one!


Sent from my iPhone using Tapatalk
twistednuts
Site Supporter
Site Supporter
Posts: 937
Joined: 07 Feb 2010, 00:37
Location: Lancashire
Re: Crank seal stator side size

Post by twistednuts »

fallenmikethebike wrote:Not without trawling through shed loads of old receipts.Perhaps on this occasion be a little reckless and order both, if you don't need it now it will be used at some time in the future.
The stator side is changed from the outside anyway, so that can be done at your leisure.
A bearing factor outlet store will have an almost identical size for considerably less than a dealer outlet.
Sorry to be negative but it's too cold out in my garage for poking about looking for stuff.
Mike
Southerners eh :roll:
fallenmikethebike
NWAA Supporter
NWAA Supporter
Posts: 3520
Joined: 02 Dec 2007, 16:02
Bike Owned: MK3
Location: Mid Surrey
Re: Crank seal stator side size

Post by fallenmikethebike »

:D The mercury was dangerously close to zero, I don't operate at my best much below 15deg C soft southern jessy. :D :D
Mike
VFORCE REEDS-MUGEN HEAD AND BARREL-WHITE POWER-ALL ON MY WISH LIST!!

Post Reply